Your over-the-range microwave is humming but the food stays cold, or it threw sparks and a puff of smoke. Call Acdc Appliance Repair and we connect you with a licensed, insured independent pro near Converse who services OTR, built-in and drawer microwaves.
A microwave is not a toaster. Inside the cabinet sits a high-voltage capacitor that can hold a lethal charge long after the plug is pulled, which is why this repair belongs with a trained technician and never with a screwdriver and a video.
Acdc Appliance Repair is a free referral service. Our dispatchers listen to the symptom, then route the call to an independent local pro who handles microwave electronics and mounting work.
The contractors in our network are independent businesses that carry the license and insurance local rules require. Ask to see both at the door.
A magnetron or control board for a built-in can be a real expense. The technician writes the quote before any work starts, so you can compare it to a replacement unit and decide.
We look for a pro already working near Converse. A same-day slot opens up regularly when local pros have breathing room, and the arrival window gets set while you are on the line.
Expect an insulated discharge tool for the capacitor, a multimeter for diode and transformer checks, the model tech sheet, and a microwave survey meter to check for leakage after high-voltage work.
These cover the over-the-range, built-in wall, drawer and convection combo models that are worth repairing. Each starts with a safe capacitor discharge before any testing.
The fan spins, the light glows, the plate turns, and the coffee comes out cold. The usual suspects are the magnetron, the high-voltage diode, the capacitor, or the transformer. The technician tests each one with the power off and the capacitor discharged.
Blue flashes along the side wall usually come from a greasy or burnt waveguide cover, chipped cavity paint, or a damaged rack support on a convection model. Left alone, arcing can pit the cavity and ruin the magnetron.
The door has several interlock switches and a monitor switch that blows the line fuse if the others fail. A totally dead microwave often means that fuse did its job. If yours runs with the door open, unplug it now and do not use it again until it is checked.
Dead buttons, phantom beeps, or a unit that keeps running after the timer ends point to the membrane touchpad or a stuck relay on the control board. The technician reads the keypad circuit with a meter and checks the relays before ordering parts.
An over-the-range microwave also works as the range hood. Grinding fans, a lamp that never turns on, greasy metal filters, and a spent charcoal filter on recirculating installs all get handled here.
A plate that will not spin usually needs a turntable motor or a new coupler. OTR units that sag or rattle may have a loose wall bracket or top bolts pulled through the cabinet, which is a safety issue with a hot stove below.
Here is a fast way to match the symptom to the likely cause. Pass it along when you call, so the pro can load the right parts for your model.
| Symptom | Common cause | What the tech checks |
|---|---|---|
| Runs, light on, no heat | Magnetron, diode, capacitor or transformer failure | Each high-voltage part with the capacitor discharged |
| Completely dead, no display | Blown line fuse from a failed door switch | Fuse, interlock switches, monitor switch |
| Sparks or smoke inside | Burnt waveguide cover, chipped cavity paint | Cover, cavity surface, stirrer, rack supports |
| Keeps running at zero or with door open | Welded relay or failed interlock | Control board relays and door switch chain |
| Plate will not turn | Turntable motor or coupler | Motor continuity, coupler, roller ring |
| Vent fan loud or dead | Fan motor bearings, greasy filters | Fan motor, damper, grease and charcoal filters |
A basic countertop microwave usually is not worth a service call, and most technicians will tell you so on the phone. Over-the-range units, built-in wall models, drawer microwaves and convection combos are a different story. They cost more, they fit a cutout or bracket, and swapping one means trim kits, cabinet work and a vent connection.
Leave the cabinet closed and pick up the phone. The dispatch line is answered around the clock.
Tell the dispatcher what type of microwave you have, whether it sits over the range, in a wall, or in a drawer, and what it is doing. If you can, read off the model number from the tag inside the door frame.
We route the job to an independent pro near Converse and give you the arrival window on the call. When the schedule cooperates, a technician often arrives the day you call.
The technician unplugs the unit, discharges the capacitor with an insulated tool, and tests the high-voltage parts, door switches and control board. OTR models may need to come off the wall plate for access. You get a written, upfront quote before work starts.
After the repair, the pro heats a cup of water to confirm output and, after any high-voltage work, sweeps the door seal with a microwave survey meter to check for leakage. Written coverage for parts and labor is the norm among the pros we connect; ask for it.
Our over-the-range microwave went completely dark mid-popcorn. The technician found a blown line fuse, then traced it to a cracked door switch. He replaced both and showed me why the fuse would have blown again if he had only swapped the fuse.
Our wall-mounted microwave ran with no heat. Replacing it meant matching a trim kit, so I asked about repair. She tested the high-voltage parts, swapped the magnetron, and ran a leakage check with a survey meter before packing up.
Blue sparks kept flashing inside the cavity. The technician pulled a waveguide cover that was charred from spatter, put in a new one, and told me how to wipe it down so it does not happen again.
The drawer microwave kept running even at zero, which scared us. The technician diagnosed a stuck relay on the control board, ordered the exact board, and installed it on a return visit.
When the light, fan and turntable all work but food stays cold, the high-voltage circuit has failed. The most common causes are a bad magnetron, a shorted diode, an open capacitor, or a burnt transformer. These parts carry lethal voltage, so let a trained technician test them.
No. Stop using it until it is checked. Sparks usually come from a dirty or burnt waveguide cover or chipped cavity paint, and continued arcing can damage the magnetron. If there is smoke, keep the door closed and unplug it if you can reach the cord safely.
Most of the time a dead microwave has blown its line fuse, and the fuse blew because a door switch failed and the monitor switch tripped it. A good pro replaces the failed switch along with the fuse, not just the fuse.
Often, yes. OTR, built-in and drawer models cost more and are sized to your cabinets, so replacing them can mean new brackets, trim and vent work. Countertop units are usually cheaper to replace. The technician gives you a written quote so you can compare.
We strongly advise against it. That capacitor stores enough energy to kill, even with the plug pulled. Keep the outer case on and leave the discharge to a technician with proper insulated tools.
Ask for it, especially after high-voltage or door work. Many pros sweep the door seal and vents with a microwave survey meter before they leave, to confirm the unit is sealed properly.
We route microwave calls from houses, condos and apartments throughout Converse and nearby neighborhoods. Dispatchers send each job to an independent pro already working close to your address, which helps when an OTR unit needs a second set of hands to lift off the wall plate.
The dispatch line is open 24 hours a day. A late-night call is usually booked for the next morning, and daytime calls often turn into same-day visits when a local pro has an opening.
